Arti Bunyi Beep pada Motherboard

Mungkin sobat kutek pernah mendengar motherboard yang kadang berbunyi beep pada saat komputer nya ada masalah, nah bunyi itu ada maksud dan artinya yang bisa jadi petunjuk dimana masalah pada komputer anda

NEW BIOS BEEPING CODE

Phoenix Award BIOS beep codes are a series of beeps separated by a pause, for example:
beep --- beep beep --- beep --- beep beep would be 1-2-1-2
1-1-4-1 - Cache Error (level 2) (Processor bermasalah)
1-2-2-3 - BIOS ROM Checksum (baterai CMOS minta diganti/BIOS bermasalah)
1-3-1-1 - DRAM Refresh Test
1-3-1-3 - Keyboard controller test
1-3-4-1 - RAM Failure on address line xxxx (check memory) (RAM bermasalah)
1-3-4-3 - RAM Failure on data bits xxxx of low byte of memory bus (RAM bermasalah)
1-4-1-1 - RAM Failure on data bits xxxx of high byte of memory bus (RAM bermasalah)
2-1-2-3 - ROM copyright notice
2-2-3-1 - Test for unexpected interrupts

AMI BIOS ERROR BEEP CODES
1 Beep - Memory Refresh Failure (check memory) (RAM bermasalah)
2 Beeps - Memory Parity Error in first 64KB block (check memory) (RAM bermasalah)
3 Beeps - Memory Read/Write Error in first 64KB block (check memory) (RAM bermasalah)
4 Beeps - Motherboard timer not functioning (possible motherboard replacement) (Motherboard bermasalah)
5 Beeps - Processor Error (may need replacement Processor) (Processor Bermasalah)
6 Beeps - Gate A20/keyboard controller failure (possible motherboard replacement) (Motherboard bermasalah)
7 Beeps - Processor Exception Interrupt Error (may need replacement Processor) (Processor Bermasalah)
8 Beeps - Display Memory Read/Write Failure (reseat or replace video card) (periksa posisi VGA/VGA bermasalah)
9 Beeps - ROM checksum Error (replace BIOS chip or motherboard) (BIOS/Motherboard bermasalah)
10 Beeps - CMOS shutdown Read/Write error (possible motherboard replacement) (Motherboard bermasalah)
11 Beeps - Bad Cache Memory - test failed (replace cache memory) (RAM bermasalah)
There are 2 main beep codes for the Award BIOS (AWARD BIOS only):
one long beep and two short beeps - Video error (reseat or replace video card) (periksa posisi VGA/VGA bermasalah)
two short beeps - Non-Fatal Error (reseat RAM, check other components) (periksa posisi RAM,periksa kondisi komponen yg lain)

Phoenix Mobo BIOS Q3.07 OR 4.X

1-1-1-3
Verify Real Mode.

1-1-2-1
Get CPU Type.

1-1-2-3
Initialize system hardware.

1-1-3-1
Initialize chipset registers with initial POST values.

1-1-3-2
Set in POST flag.

1-1-3-3
Initialize CPU registers.

1-1-4-1
Initialize cache to initial POST values.

1-1-4-3
Initialize I/O.

1-2-1-1
Initialize Power Management.

1-2-1-2
Load alternate registers with initial POST values.

1-2-1-3
Jump to UserPatch0.

1-2-2-1
Initialize keyboard controller.

1-2-2-3
BIOS ROM checksum.

1-2-3-1
8254 timer initialization.

1-2-3-3
8237 DMA controller initialization.

1-2-4-1
Reset Programmable Interrupt Controller.

1-3-1-1
Test DRAM refresh.

1-3-1-3
Test 8742 Keyboard Controller.

1-3-2-1
Set ES segment to register to 4 GB.

1-3-3-1
28 Autosize DRAM.

1-3-3-3
Clear 512K base RAM.

1-3-4-1
Test 512 base address lines.

1-3-4-3
Test 512K base memory.

1-4-1-3
Test CPU bus-clock frequency.

1-4-2-4
Reinitialize the chipset.

1-4-3-1
Shadow system BIOS ROM.

1-4-3-2
Reinitialize the cache.

1-4-3-3
Autosize cache.

1-4-4-1
Configure advanced chipset registers.

1-4-4-2
Load alternate registers with CMOS values.

2-1-1-1
Set Initial CPU speed.

2-1-1-3
Initialize interrupt vectors.

2-1-2-1
Initialize BIOS interrupts.

2-1-2-3
Check ROM copyright notice.

2-1-2-4
Initialize manager for PCI Options ROMs.

2-1-3-1
Check video configuration against CMOS.

2-1-3-2
Initialize PCI bus and devices.

2-1-3-3
Initialize all video adapters in system.

2-1-4-1
Shadow video BIOS ROM.

2-1-4-3
Display copyright notice.

2-2-1-1
Display CPU Type and speed.

2-2-1-3
Test keyboard.

2-2-2-1
Set key click if enabled.

2-2-2-3
56 Enable keyboard.

2-2-3-1
Test for unexpected interrupts.

2-2-3-3
Display prompt Press F2 to enter SETUP.

2-2-4-1
Test RAM between 512 and 640k.

2-3-1-1
Test expanded memory.

2-3-1-3
Test extended memory address lines.

2-3-2-1
Jump to UserPatch1.

2-3-2-3
Configure advanced cache registers.

2-3-3-1
Enable external and CPU caches.

2-3-3-3
Display external cache size.

2-3-4-1
Display shadow message.

2-3-4-3
Display non-disposable segments.

2-4-1-1
Display error messages.

2-4-1-3
Check for configuration errors.

2-4-2-1
Test real-time clock.

2-4-2-3
Check for keyboard errors

2-4-4-1
Set up hardware interrupts vectors.

2-4-4-3
Test coprocessor if present.

3-1-1-1
Disable onboard I/O ports.

3-1-1-3
Detect and install external RS232 ports.

3-1-2-1
Detect and install external parallel ports.

3-1-2-3
Re-initialize onboard I/O ports.

3-1-3-1
Initialize BIOS Data Area.

3-1-3-3
Initialize Extended BIOS Data Area.

3-1-4-1
Initialize floppy controller.

3-2-1-1
Initialize hard disk controller.

3-2-1-2
Initialize local bus hard disk controller.

3-2-1-3
Jump to UserPatch2.

3-2-2-1
Disable A20 address line.

3-2-2-3
Clear huge ES segment register.

3-2-3-1
Search for option ROMs.

3-2-3-3
Shadow option ROMs.

3-2-4-1
Set up Power Management.

3-2-4-3
Enable hardware interrupts.

3-3-1-1
Set time of day.

3-3-1-3
Check key lock.

3-3-3-1
Erase F2 prompt.

3-3-3-3
Scan for F2 key stroke.

3-3-4-1
Enter SETUP.

3-3-4-3
Clear in POST flag.

3-4-1-1
Check for errors

3-4-1-3
POST done - prepare to boot operating system.

3-4-2-1
One beep.

3-4-2-3
Check password (optional).

3-4-3-1
Clear global descriptor table.

3-4-4-1
Clear parity checkers.

3-4-4-3
Clear screen (optional).

3-4-4-4
Check virus and backup reminders.

4-1-1-1
Try to boot with INT 19.

4-2-1-1
Interrupt handler error.

4-2-1-3
Unknown interrupt error.

4-2-2-1
Pending interrupt error.

4-2-2-3
Initialize option ROM error.

4-2-3-1
Shutdown error.

4-2-3-3
Extended Block Move.

4-2-4-1
Shutdown 10 error.

4-3-1-3
Initialize the chipset.

4-3-1-4
Initialize refresh counter.

4-3-2-1
Check for Forced Flash.

4-3-2-2
Check HW status of ROM.

4-3-2-3
BIOS ROM is OK.

4-3-2-4
Do a complete RAM test.

4-3-3-1
Do OEM initialization.

4-3-3-2
Initialize interrupt controller.

4-3-3-3
Read in bootstrap code.

4-3-3-4
Initialize all vectors.

4-3-4-1
Boot the Flash program.

4-3-4-2
Initialize the boot device.

4-3-4-3
Boot code was read OK.